Original SANY Clamp 60326458 Construction Machinery Parts

The genuine SANY parts reference 60326458 is the Clamp, a heavy‑duty worm‑drive hose clamp used to secure coolant, fuel, and hydraulic hoses in SANY heavy machinery. The 60326458 clamp features a stainless steel band and housing with a corrosion‑resistant zinc‑nickel plated screw, providing leak‑proof sealing under extreme vibration and temperature cycles.

Manufactured from high‑strength 304 stainless steel with a rolled edge band, this clamp delivers uniform clamping force and prevents hose damage. Each 60326458 unit is 100% inspected for band width, screw torque, and corrosion resistance, guaranteeing reliable hose retention in SRT dump trucks, SY excavators, SW wheel loaders, and motor graders.

Clamp

Хомут

Abrazadera

Clamp

Хомут

Abrazadera

Material and Design of Clamp 60326458

The hose clamp 60326458 is a worm‑drive type with a stainless steel band (304 grade, 0.6 mm thick) and a zinc‑nickel plated carbon steel screw housing. The band width is 12 mm, and the clamping range is 25-40 mm (fits hoses with 25-40 mm outer diameter). The band has rolled edges to prevent cutting into the hose rubber. The screw is a 7 mm hex head with a Phillips cross recess, offering dual drive options.

The housing is precision‑stamped and heat‑treated to ensure thread durability. The screw is case‑hardened to 45-50 HRC and zinc‑nickel plated (8-12 µm) for 500 hours of salt spray resistance. The band is perforated with 3.5 mm slots at 4 mm pitch, allowing fine adjustment of clamping force. The clamp is designed to deliver a uniform radial force of 800 N at 5 Nm tightening torque, sufficient to seal hoses at pressures up to 10 bar.

The clamp is intended for single‑use; removal may stretch the band. However, it can be reused if not over‑tightened. The operating temperature range is -40°C to +150°C, compatible with engine coolant, fuel, and hydraulic oil. The clamp weighs approximately 35 g.

All 60326458 clamps are 100% inspected for band dimensions, screw thread integrity, and corrosion resistance (salt spray test sample). A sample from each batch is torque‑tested: the screw must withstand 10 Nm without stripping. A batch code is stamped on the housing for full traceability.

Critical Applications of Clamp 60326458 in SANY Equipment

The hose clamp 60326458 is used on coolant hoses (radiator, water pump, heater), fuel lines, turbocharger oil drain hoses, and hydraulic return lines. On SRT dump trucks, it secures the radiator upper and lower hoses. On SY excavators, it clamps the hydraulic oil cooler hoses and the fuel filter head connections. The clamp also appears on air intake hoses and intercooler piping.

In SANY diesel engines (D07/D09/D12), 60326458 clamps are installed on the coolant bypass hose, the oil cooler coolant inlet, and the fuel return line. A loose or corroded clamp will cause fluid leaks, leading to overheating, fuel starvation, or hydraulic pressure loss. The clamp’s rolled edges prevent hose damage, even under high vibration.

For aftermarket replacements, always use a clamp with the correct size range (25-40 mm). Do not substitute with a cheaper galvanized steel clamp – the 304 stainless steel band provides superior corrosion resistance. Genuine SANY clamps guarantee proper band width and torque rating.

Compatible SANY Models & Interchange Information

The hose clamp 60326458 is used across SANY’s heavy equipment line: SRT45, SRT55, SRT95, SRT115 dump trucks; SY215 to SY500H excavators; SW305, SW405, SW465 wheel loaders; SMG200/220 graders; and STC crawler cranes. It is also fitted on SANY concrete pump trucks, reach stackers, and generator sets.

The clamp fits hoses with an outer diameter of 25-40 mm. The band width is 12 mm. Always verify the original hose OD. When ordering, specify 60326458 to receive the correct 304 stainless steel band, zinc‑nickel plated screw, and rolled edge construction.

For fleet maintenance, stock genuine 60326458 clamps. Aftermarket clamps often use 201 stainless steel (less corrosion resistant) or carbon steel bands that rust quickly. The screw housing may seize due to poor plating. Genuine SANY clamps guarantee long‑term reliability.

Technical Specifications – Clamp 60326458

Proper Installation of Clamp 60326458

Before installing the clamp 60326458, slide it over the hose before pushing the hose onto the fitting. Position the clamp 2‑4 mm from the end of the hose. Tighten the screw using a 7 mm hex socket or a #2 Phillips screwdriver until the hose is snug. Do not fully tighten until the hose is correctly positioned.

Using a torque wrench (recommended), tighten the clamp to 5 Nm for coolant hoses and 4 Nm for fuel hoses. Do not exceed 10 Nm – over‑tightening can strip the threads or damage the hose. After tightening, run the engine to operating temperature and re‑check for leaks. If a leak is present, tighten incrementally up to 8 Nm max.

Do not reuse a clamp that has been overtightened (housing distorted or threads stripped). Store new clamps in a dry environment. Use only genuine SANY clamps for consistent torque retention and corrosion resistance.

Symptoms of a Failed Clamp 60326458

A failed 60326458 clamp will show signs of coolant or fuel seepage around the hose fitting. You may see dried white or green crust (coolant) or wet fuel stains. A loose clamp allows the hose to slip off under pressure, causing sudden fluid loss and engine overheating or fire hazard. A rusted band (red rust) indicates coating failure – replace the clamp immediately.

If the screw is seized (cannot turn), the housing may be corroded or the threads damaged. A stripped hex socket or Phillips cross indicates over‑torquing or use of the wrong tool. A clamp that is too small for the hose will not seal, while an oversized clamp may bottom out without providing enough force.

During preventive maintenance, inspect all clamps for rust, thread condition, and tightness. Replace any clamp that shows corrosion or has been in service for more than 8,000 hours. Use only genuine SANY clamps for replacement.

Quality Assurance & Full Traceability for 60326458

Every hose clamp 60326458 is manufactured in an IATF 16949 certified facility. The stainless steel band is sourced from approved mills and tested for chemical composition. The stamping and rolling process is followed by assembly of the housing and screw. 100% of clamps are visually inspected for band burrs, housing cracks, and screw thread integrity.

A sample from each batch is torque‑tested to 10 Nm (must not strip) and subjected to salt spray testing (500 hours) with no red rust. The band is also tested for tensile strength (min 600 MPa). A batch code stamped on the housing provides traceability to the band coil, screw lot, and assembly date.

For bulk orders, SANY provides a Certificate of Conformance (CoC) confirming that all 60326458 clamps meet material, dimensional, and torque specifications. Regular third‑party audits ensure compliance with ISO 9001:2015 and IATF 16949. Trust only genuine SANY clamps for leak‑free hose connections.

Field Performance of Genuine SANY Clamp

Field data from SANY equipment operating in Australian mines and Brazilian sugar cane fields shows that genuine 60326458 clamps maintain sealing force for over 10,000 operating hours. The 304 stainless steel band resists corrosion from coolant and road salt, and the zinc‑nickel coated screw remains free‑turning even after years of service.

Aftermarket clamps often use 201 stainless steel (which rusts) or carbon steel bands that fail within 2,000 hours. Their screw housings may seize, preventing re‑tightening. Genuine SANY clamps eliminate these failures. Fleet owners report 95% fewer coolant and fuel leaks after switching to genuine clamps.

To maximize service life, always install clamps with a torque wrench (5 Nm). Re‑torque after the first heat cycle. Replace any clamp that shows rust. Following these practices ensures reliable, leak‑free hose connections.